OUTPUT mode 2:
Connect the COM pin with any other Additional Power Supply,the output will create the same Voltage signal as the Additional Power Supply. it can be Direct Current or Alternating Current. Decided by the Additional Power Supply.
BUT, Please note: the additional Power Supply should be in the range of the Receiver Switch Module-(DC5-12V, AC 85-240V).
Please check below diagram for better understanding.
OUTPUT mode 3:
Connect the COM pin with any other device, the it can be used as switches to oper door, control motor or control fun ect.
IMPORTANT INFORMATIONS:
You can match the Remote Control with the Receiver SwitchModule in 4 mode:
Remote mode 1: Momentary/Jog
Press and hold one key->ON; Release the key->OFF
Details:
Hold one key , the corresponding channel is working /ON;Then Release your finger the channel turns to stop/OFF .
Remote Mode 2: Toggle/Self-Lock
Press one Key->ON; Press the same key again->OFF
Details:
Press one key once , the corresponding channel turn working/ON;
Press the same key once again the same channel turn to stop/OFF .
Remote Mode 3: Latched/Inter-Lock
Press one Key once->ON; Press another key once->OFF
Details:
Press one key once( take A key for example), the corresponding channel (like channel 1) turn to working/ON;
Press another key once(take B key for example), the same channel turn to stop/OFF. At the same time, another corresponding channel(like channel 2) turn to working / ON .
Remote Mode 4: Time delay mode
Press and hold one key->ON; Release the key->OFF(after 5 seconds,or 10 seconds,or 15 seconds, 3 ways of the time delay can be chosen)
Details:
Hold one key , the corresponding channel is working /ON;Then Release your finger the channel turns to stop/OFF .after 5 seconds,or 10 seconds,or 15 seconds.3 ways of the time delay can be chosen!
Note: When you receive the product, it maybe set in one remote mode randomly, that because each product got test when it can be arranged to shipment.So, if you want to select the remote mode you like, please Delete the existing data for the first step:
How to Delete the existing remote controls data?
Press the learning key on the Receiver Switch Module board 8 times, then wait for the LED indicator on the board flash for 7 times, the existing data are deleted successfully. ( if the LED indicator on the board doesn’t Flash, Please check the Power Supply status, make it right, and try more times)
Please find the Learning Key of the Receiver Switch Module by checking below photo:
How to Set the Remote Mode:
1-Momentary/Jog Mode:
Press the learning key on the Receiver Switch Module board once , The ON-board Led indicator will Flash simultaneously .
Then press any of the remote key (Or which one your want to use) , the on-board LED indicator will flash 5 times to inform that the setting of momentary mode is successful .
2-Toggle/Self-Lock:
Press the learning key on the Receiver Switch Module board 2 times.The ON-board Led indicator will Flash simultaneously .Then press any of the remote key (Or which one your want to use) , the on-board LED indicator will flash 5 times to inform that the setting of toggle mode is successful .
3-Latched/Inter-Lock:
Press the learning key on the Receiver Switch Module board 3 times.The ON-board Led indicator will Flash simultaneously .
Then press first remote key (Like Key A), then press the a second Key (Like Key B), the on-board LED indicator will flash 5 times to inform that the setting of latched mode successful . The first pressed key stands for on(Like Key A ), and the second pressed Key stands for off (Like Key B).
4-Time Delay
Press the learning key on the Receiver Switch Module board forth times, the time delay for 5 seconds .
Press the learning key on the Receiver Switch Module board fifth times, the time delay for 10 seconds .
Press the learning key on the Receiver Switch Module board sixth times, the time delay for 15 seconds .
The LED indicator will be off after the learning key operations.
Then Press one of the remote keys, LED flashes and turn off .
After 3 seconds, the LED indicator will be on again, delay mode set successfully .
Product SPECIFICATION:
Electronics Character:
Input Power: DC10V-14V
Standby Current: <5MA
RF Frequency: 315M or 433M
RF working mode: superheterodyne
Receive sensitivity: >97dbm
Transmitting distance: 20 meters above
Decoding mode: MCU software decoding
Remote storage: 25 pcs
Support remote type: Learning code, Fixed code(Rolling code can be design)
Working mode: Momentary, Toggle, Latching Time delay (5s ,10s ,15s )
Wiring type: fixed terminal
Output Terminal: NO , NC , COM
Dimension of PCB: 35*30*18mm (L,W,H)
Pin functions:
Wiring diagram 1:
+V: 12V + input ;
– V: 12V – input ;
NO: Output , normal open;
COM:Output , common ;
NC: Output , normal close;
Product Photos:
NOTE: